Give Mirabel Magical Powers. Activities for Kids.

All Activities

Give Mirabel Magical Powers

Make a glowing magic bracelet for Mirabel using beads, an LED, and a coin cell, then invent powers and perform a short story.

Start Creating

Table of contents

Step-by-step guide to make a glowing magic bracelet for Mirabel

0:00/0:00

Here at SafeTube, we're on a mission to create a safer and more delightful internet. 😊

Encanto | All family magical powers revealed, exclusive clip analysis, key themes and concept art

What you need

Adult supervision required, beads, clear tape, coin cell battery, elastic cord, led, scissors, small scrap of felt or thick paper

Step 1

Gather all materials and place them on a clean table.

Step 2

Hold the elastic around your wrist to find a comfy size.

Step 3

Cut the elastic at that spot leaving about 2 cm extra for tying.

Step 4

Thread beads onto the elastic but stop when you reach the center so there is room for the LED and battery.

Step 5

Push the LED bulb into the center front of the bead strand so the plastic bulb faces out and the two metal legs stick out to the sides.

Step 6

Tape the coin cell to the elastic behind the beads with the flat side labeled + facing outward.

Step 7

Carefully press the longer LED leg onto the flat + side and the shorter leg onto the opposite side so the LED lights when they touch.

Step 8

Secure each LED leg to the coin cell with small pieces of tape and cover any exposed metal to prevent shorting.

Step 9

Slide more beads over the taped battery area to hide it and keep the bulb centered.

Step 10

Tie a strong double knot in the elastic ends to close the bracelet.

Step 11

Trim the extra elastic and tuck the knot into a nearby bead or cover it with tape.

Step 12

Invent three magical powers Mirabel gets from the glowing bracelet and write or say one sentence for each power.

Step 13

Practice and then perform a short story where Mirabel uses her three powers and the glowing bracelet to solve a problem.

Step 14

Share a photo or short video of your glowing Mirabel bracelet and your story on DIY.org.

Final steps

You're almost there! Complete all the steps, bring your creation to life, post it, and conquer the challenge!

Complete & Share

Help!?

What can we use if we can't find coin cell batteries or small LEDs?

Use a pre-wired LED charm or a small battery-operated LED module (from craft or dollar stores) in place of the loose LED and coin cell and tape or thread it to the elastic following the same steps to hide it with beads.

My LED doesn't light—what should I check?

Make sure the coin cell is taped with the flat side labeled + facing outward as instructed, that the longer LED leg presses on the + side and the shorter leg on the opposite side, and that you secure and cover any exposed metal with tape so the legs don't short.

How can we adapt this activity for younger or older kids?

For younger children have an adult pre-cut the elastic, pre-thread or supervise threading of large beads, and handle the coin cell taping and knot-tying, while older kids can experiment with adding extra LEDs or making a decorative clasp instead of tying a knot.

How can we personalize or extend the glowing Mirabel bracelet and story?

Personalize the bracelet by assigning a bead color to each invented power, add a second colored LED for different effects and use the 'invent three magical powers' step to write a longer, illustrated story or perform a group scene with props.

Watch videos on how to make a glowing magic bracelet for Mirabel

0:00/0:00

Here at SafeTube, we're on a mission to create a safer and more delightful internet. 😊

Mirabel Didn't Get a GIFT?! 🌟 | Encanto | Disney Kids

4 Videos

Facts about basic electronics and wearable crafts

🔋 A common coin cell like the CR2032 provides about 3 volts—always have an adult help with batteries and disposal.

🎬 Encanto's soundtrack became a surprise chart-topper — the song "We Don't Talk About Bruno" reached #1 on the US Billboard Hot 100.

💡 LEDs are tiny, energy-efficient lights that use very little current, which makes them great for battery-powered craft bracelets.

🧚 Mirabel Madrigal is the young heroine of Disney's Encanto who doesn't receive a magical gift, so she finds strength in courage and creativity.

📿 People have worn bead bracelets for thousands of years—archaeologists have found ancient bracelets made from shells and stones.

How do I make a glowing magic bracelet for Mirabel and perform a short story?

To make the glowing bracelet, thread beads onto elastic or thin jewelry wire leaving space for an LED. Push the LED leads through bead holes, noting polarity (the longer lead is +). Secure each lead to the coin cell with a holder or small pieces of tape so the LED lights. Hide the battery between beads and cover connections with tape. Finally, invent Mirabel’s powers, practice a short scene, and perform the story with the glowing bracelet on.

What materials do I need to make a glowing Mirabel magic bracelet?

You’ll need a small LED (3–5 mm), a coin cell battery (e.g., CR2032), and either a coin-cell holder or electrical tape to secure the connection. Also gather elastic cord or thin jewelry wire, beads with holes big enough for LED leads, scissors, pliers or tweezers, and electrical tape or heat-shrink tubing. Optional extras: charms, glow-in-the-dark beads, and a marker for decorating. Have adult supervision and a small container for tiny parts.

What ages is the Mirabel glowing bracelet activity suitable for?

This activity is best for children ages 6 and up with adult supervision. Kids 6–8 can help select beads and thread elastic while adults handle the battery connections and trimming. Ages 9–12 can do more of the assembly with guidance. It’s not recommended for children under 6 due to small parts and coin-cell hazards. Adjust storytelling complexity and fine-motor steps to match each child’s skills.

Is it safe to use LEDs and coin cells in children's crafts and how can I keep it safe?

Coin cells are a serious swallowing hazard, so always supervise closely and keep spare batteries out of reach. Use a battery holder or securely tape the coin cell so it can’t pop out. Trim and tape sharp wire ends and teach kids to remove the battery when not in use. Dispose of used batteries safely. For a safer variation, use a sealed LED module or glow-in-the-dark beads instead of a loose coin cell.

One subscription, many ways to play and learn.

Try for free

Only $0 after trial. No credit card required

To create a safe space for kid creators worldwide!

Popular Activities

How to Make Slime

Draw a Dog

Code with Scratch

Create pop-up box

Cook Salmon

Popular Courses

Cook for Yourself

Secrets of Drawing

Strange science

Invent Your Machines

Build anything with Lego

Popular Wikis

Famous Architects

Pottery

Painting

Capitals

Political Leaders

Discovery Tools

Kids GPT

DIY Wiki

Magic Atlas

DIY TV

Creativity Tools

How to draw

Super Draw

Games & Fun

Would You Rather

Jokes for kids

Teacher Tools

SafeTube

DIY Blog

Product

Log-in

Sign-up

Download for iOS

Download for Android

Pricing

FAQ

Company

About

Community guideline

2025, URSOR LIMITED. All rights reserved. DIY is in no way affiliated with Minecraft™, Mojang, Microsoft, Roblox™ or YouTube. LEGO® is a trademark of the LEGO® Group which does not sponsor, endorse or authorize this website or event. Made with love in San Francisco.